End-to-end VFD engineering — drive selection, sizing, parameterisation, EMC filter design, brake-resistor sizing and full motor-load commissioning — for pumps, fans, conveyors, mixers, compressors and machine tools from 0.4 kW to 500 kW across ABB, Siemens, Schneider, Danfoss, Yaskawa & Delta drives.
From sizing the right drive for a single 5 kW pump to commissioning 500 kW process drives with regen braking — six core engineering capabilities, fully accountable.
Right drive for the right load — calculated from motor data, load profile, ambient conditions, duty cycle and start/stop frequency. Avoid oversizing waste & undersizing failures.
Application-specific drive programming — V/Hz, sensorless vector, closed-loop vector or DTC — with PID, ramps, jog modes, S-curves and start-up routines configured for your process.
EMC compliance is critical — line filters, line reactors, output dV/dt filters and sine-wave filters sized correctly to meet IEC 61800-3 limits and protect motor insulation on long cable runs.
Drive integration into your control system — Profinet, EtherNet/IP, Modbus TCP/RTU, CANopen or Profibus — with PLC function blocks, parameter access & status monitoring.
Most pumps, fans & compressors run far below rated load. Replacing star-delta starters with VFDs typically saves 20–40% energy with payback in 12–24 months — we measure, report and prove the savings.
Beyond standard VFDs — soft starters for high-inrush pumps & compressors, DC drives for legacy DC motors, and active-front-end / regenerative drives for hoists & lifts.
From municipal water pumps to mine-shaft conveyors and process-industry mixers — VFDs are the workhorse of efficient electrical drives across every African industrial sector.
Every VFD project follows the same disciplined path — from load profiling and drive sizing through commissioning, tuning and energy savings verification.
Motor data, load profile, ambient, duty cycle & supply quality
Drive model, EMC filter, reactor, brake resistor, cabling
V/Hz, vector or DTC config; PID, ramps, comms set-up
Drive bench-tested with motor & load simulation
No-load run, on-load tuning, vibration & current check
Post-install savings measurement, operator training, AMC
Our drive engineers are experienced across the world's leading VFD brands — ABB, Siemens, Schneider, Danfoss, Yaskawa, Delta & Lenze — so we recommend the right drive for your motor and load, not just one OEM.
Whether you're standardising on ABB ACS880, retrofitting Sinamics G120 across a plant, or upgrading legacy Mitsubishi A700s to A800s, we deliver sizing, supply, parameterisation, commissioning & tuning across every major drive family.
ABB Drive Composer, Siemens Sinamics, Danfoss MCT 10, Yaskawa DriveWorks — engineers across all major drive families.
We size based on motor data, load profile, ambient and duty cycle — no over-spec waste, no under-spec failures.
EMC, derating, ambient temperature, voltage tolerance, dust ingress all factored — drives don't trip on hot afternoons.
Secure VPN remote-access into drive parameters and PLC — most trips diagnosed within 1 hour without travel.
Pre- & post-installation kWh measurement & reporting — energy savings claims are proven, not marketed.
We supply the drive, EMC filter, reactor, panel build, programming & commissioning — single vendor, single accountability.
Tell us about your application — pump, fan, conveyor, mixer, hoist or process drive. Our drive engineers will respond with sizing, brand recommendation, EMC scope and full proposal with CIF / on-site pricing.
Outline your application — we'll respond with detailed sizing, drive selection & commercial scope within 5 working days.
Common questions about variable frequency drive supply for Africa.
VFD (Variable Frequency Drive) systems control motor speed for pumps, fans, compressors and conveyors, improving energy efficiency and process control.
We supply VFD and variable speed drives to Nigeria, Kenya, Ghana, Tanzania, Zambia and other African countries.
We supply AC drives, servo drives and soft starters for a range of industrial motor applications.
Yes. VFDs significantly reduce energy consumption by matching motor speed to actual process demand instead of running at full speed constantly.
Yes. We provide installation, programming and commissioning support for all VFD systems we supply.
Contact us via WhatsApp with your motor specifications and application for a detailed quotation.
Chat on WhatsAppReply within minutes